Repair and Restoration

How to Use a Timegrapher to Regulate a Watch

How a timegrapher works, what beat rate, amplitude and beat error tell you, and how to regulate a mechanical watch with a gooseneck regulator.

On this page
  1. What a Timegrapher Measures
  2. Beat Rates Explained
  3. Setting Up the Machine
  4. Reading the Graph
  5. Testing in Several Positions
  6. What Is a Gooseneck Regulator?
  7. Regulating With a Gooseneck
  8. Regulating Without One
  9. Common Mistakes
  10. Gooseneck FAQ
  11. When to Leave Regulation to a Watchmaker

A timegrapher, also called a timing machine or watch escapement analyzer, listens to or watches a mechanical watch’s balance wheel as it ticks. It turns those ticks into a graph and a set of figures that show how accurately the watch is running. If you searched for a microset watch timer, the same principles apply to any timing machine of this type.

What a Timegrapher Measures

A timing machine reports four main values:

  • Rate. How many seconds per day the watch gains or loses, measured over a period of time.
  • Amplitude. How far the balance wheel swings, measured in degrees. Amplitude tends to fall as lubricant ages, the mainspring weakens or dirt builds up.
  • Beat error. How evenly the balance swings in each direction. A large beat error often points to a balance or escapement problem. Ideally it is close to zero.
  • Beat rate. How many ticks per hour the movement makes. The movement design sets this figure.

Beat Rates Explained

Beat rates are quoted in beats per hour (bph). Each full swing of the balance produces two ticks, so the frequency in hertz is the bph figure divided by 7,200. Common rates include:

  • 18,000 bph, or 2.5 Hz
  • 21,600 bph, or 3 Hz
  • 28,800 bph, or 4 Hz
  • 36,000 bph, or 5 Hz

Enter the correct beat rate for your movement in the machine, or the readings will be wrong. The movement’s specification or the caseback often shows it.

Setting Up the Machine

  1. Place the timing machine on a stable, level surface, away from vibration and direct light.
  2. Position the watch in its holder so the microphone or sensor sits directly on the case, as the machine’s instructions describe.
  3. Wind the watch fully before measuring, and allow it a few minutes to settle before you take readings.
  4. Enter the beat rate, then check that the readings hold steady.

Reading the Graph

Most timing machines show a graph of the beat signal. Look for:

  • a steady, regular beat pattern
  • beat error close to zero
  • amplitude that holds reasonably steady over the reading period
  • a rate that stays steady rather than wandering

Target amplitude varies by movement and design, so compare your readings with the range expected for that movement rather than a single number. A sudden drop in amplitude is a warning sign. It often points to dried lubricant, dirt or low power.

Testing in Several Positions

A watch can run differently in different positions, because gravity acts on the balance differently in each. Test in several positions, commonly:

  • dial up
  • dial down
  • crown up
  • crown down
  • crown left or right, if your machine and watch allow it

Adjust so the rate is as consistent as possible across positions. Do not chase one perfect reading.

What Is a Gooseneck Regulator?

A gooseneck regulator, also called a swan-neck regulator, is a fine-adjustment mechanism on the balance cock of some mechanical movements. Its name comes from the curved spring, which resembles a goose’s or swan’s neck. A small screw turns the regulator, changing the effective length of the balance spring and shifting the rate in very small steps.

Without a gooseneck, regulating a watch usually means moving a regulator arm by hand with a tool. A gooseneck makes small adjustments more controlled and easier to repeat.

Regulating With a Gooseneck

  1. Take a baseline reading in the dial-up position and note the rate.
  2. Turn the regulator screw in a very small increment. Which direction makes the watch faster or slower depends on the movement, so check its design before you start.
  3. Wait for the reading to settle, then compare it with the baseline.
  4. Repeat the test in the other positions.
  5. Stop when the rate is steady and within the range you need.

Adjust in small steps and wait between them. Large changes overshoot, which makes the watch harder to correct.

Regulating Without One

Some watches have a regulator arm instead of a gooseneck. Moving it takes care, because a small slip can bend a regulator pin, shift the balance spring out of position or damage the hairspring. Many people leave this work to a watchmaker. If you do try it, change the regulator in tiny steps and check that the balance spring still sits flat.

Common Mistakes

  • Reading the rate right after winding, before the watch has settled.
  • Adjusting in large steps.
  • Ignoring differences between positions.
  • Measuring on an unstable surface.
  • Trying to fix a low amplitude or a large beat error with regulation alone. Those usually need cleaning, lubrication or a repair.

Gooseneck FAQ

Which country is Seagull from? Seagull is a Chinese watch brand. Its movements, such as the 1963 chronograph, are often cited as examples of a gooseneck regulator in an affordable mechanical watch.

Is Seagull a luxury brand? Seagull is generally regarded as an affordable mechanical brand rather than a luxury one. Enthusiasts often value it for the movement design at its price.

When to Leave Regulation to a Watchmaker

Take the watch to a watchmaker if:

  • the amplitude is low or falls quickly
  • the beat error is large or unstable
  • the rate changes a lot between positions
  • the watch stops or runs in short bursts
  • you are not confident about making very small adjustments

Regulation can correct timing, but it cannot fix a worn or dry movement. For that, see the service interval guide. For a wider starting point on mechanical watch work, see watch restoration for beginners. If you are setting up a watch for the first time, the guide to setting a watch for the first time covers that step.

The complete guide to repair and restoration

Watch Restoration for Beginners: Tools and First Projects
Read the guide

Keep exploring

Guides from other topics

All topics →