The mainspring is the spring inside the barrel that stores the energy driving a mechanical pocket watch. When it is weak, broken or the wrong size, the watch loses power quickly or stops altogether. Replacing a mainspring is a useful skill for pocket watch owners, but it needs care, because the spring holds a lot of energy.
A replacement spring must match the barrel in size and hook type. Measure the old spring and the barrel, compare those measurements with a supplier’s chart, and wear eye protection while you work.
What a Mainspring Does
A mainspring is a long, thin strip of spring steel coiled inside a barrel. Winding the watch tightens the spring. As the spring slowly unwinds, it turns the barrel, which drives the gear train. The watch’s power reserve depends on the spring’s strength and the size of the barrel.
Safety First: Stored Energy
A wound mainspring stores a significant amount of energy, and it can release suddenly. Treat it with respect:
- Wear eye protection whenever you handle a mainspring or barrel.
- Hold the barrel securely in a proper holder or barrel vise. Do not hold it loosely in your fingers.
- Never release the arbor (the central post) while the spring is under tension. Use the correct tool for the job.
- Work slowly and keep your face and hands out of the line of the spring.
- Stop if the spring is cracked or broken. A broken spring can fly out. Take it to a professional.
Measurements That Decide the Right Spring
Two springs of the same length can still fit different barrels. Record these before you order:
| Measurement | Why it matters |
|---|---|
| Barrel inner diameter | The spring must fit inside the barrel wall |
| Barrel height (depth) | The spring’s width must suit the available space |
| Spring width (height) | Must match the barrel |
| Spring thickness | Affects strength and power reserve |
| Spring length | Affects how many turns it can store |
| Hook or eye type | Determines how the spring attaches to the barrel and arbor |
| Arbor size | The central post the spring hooks onto |
Use a micrometer or calipers for the diameter and thickness measurements. If you cannot measure the old spring, measure the barrel carefully and use a supplier’s chart based on your movement’s size and maker.
Reading a Sizing Chart
A sizing chart links a movement size, usually given in Lancashire sizes, to spring or barrel dimensions. Charts differ between suppliers and makers, so a chart from one source may not match another. Check:
- the maker and movement size listed on the chart
- whether the chart gives barrel dimensions or spring dimensions
- whether the hook type matches your spring
If the numbers do not match exactly, do not force the fit. Ask a supplier or an experienced watchmaker. For background on movement sizes, see the pocket watch size guide.
Removing the Old Mainspring
Work on a clean, padded surface with the right holder.
- Remove the movement from the case and note its orientation.
- Secure the barrel in a holder with the arbor accessible.
- Release the spring slowly and under control, following the method for your barrel.
- Remove the spring. Note how it sits in the barrel, the direction of the coil, and the position of the hook.
- Check the barrel for cracks, burrs, rust and debris. Clean the barrel before fitting anything new.
Fitting the New Mainspring
- If the procedure calls for it, lubricate the barrel wall lightly, using only the oil recommended for barrels.
- Fit the hook into the barrel and onto the arbor, keeping the coil direction correct.
- Wind the spring gently with a winder. Check that it sits flat and does not slip.
- Check that the spring winds and unwinds smoothly. If it binds or pulls to one side, stop and check the fit.
- Reassemble the barrel and test the movement before closing the case.
A new spring may need some adjustment to sit properly in the barrel. If it still does not seat well, do not keep forcing it. Get advice first.
How Often Should I Wind My Pocket Watch?
Hand-wind pocket watches are wound by turning the crown. Wind gently until you feel resistance, then stop, and do not force the crown past that point. Many owners wind once a day, but the right frequency depends on the watch’s power reserve, so check the manual or the maker’s guidance. Winding at a regular time each day makes the watch easier to keep consistent.
When to Leave It to a Watchmaker
Take the job to a professional if:
- the spring is broken, cracked or badly set
- the barrel is damaged
- you are unsure about any measurement
- the watch is valuable, rare or vintage
- the movement shows other faults, such as a worn gear train
For a view on whether a pocket watch is worth repairing at all, the guide to telling if a pocket watch is worth money explains what affects value. For a broader starting point, see watch restoration for beginners. The movement cleaning article explains why the movement itself should be cleaned by a professional.