Remove the movement from the case, protect the dial with a plastic sheet, and lift the second hand first, then the minute and hour hands. Use a hand puller with even, straight-up pressure, never a sideways prying motion. Refit in reverse order, with the hour hand first, using a hand press. If the dial is valuable or a hand is stuck, take the watch to a professional.
Before You Start
Ask whether the job is necessary. Hands are usually removed for a dial swap, a new hand set, a dial repair or a movement service. If none of those apply, leave them alone.
Check a few things first:
- Is the dial vintage or luminous? Older dials can have radium-based luminous paint, which is easily damaged. See the section on luminous dials below.
- Is the watch under warranty? Removing hands may affect a warranty, so check the terms.
- Are the hands original? Original hands often matter to collectors, so keep them safe.
Tools You Need
- Hand puller or hand levers. A Presto-style hand puller or a set of hand levers lifts hands straight up.
- Dial protector. A thin plastic sheet with a central hole, which protects the dial.
- Movement holder or pegwood. Holds the movement steady without marking it.
- Tweezers. For picking up and placing hands.
- Hand press. For refitting hands evenly. Use the press that suits your watch.
- A small envelope or tray. For storing the hands and any spacer washers.
- A magnifier. For checking alignment and clearances.
Step 1: Remove the Movement From the Case
Remove the strap or bracelet, open the caseback, and release the stem as the design requires. Lift the movement out with the dial side up. Support it in a holder so it does not rest on the hands or the dial.
Step 2: Align the Hands
Turn the crown so that all three hands sit roughly together near the 12 o’clock position. Aligned this way, the hands are easier to grip and the tool sits more evenly under each one.
Step 3: Protect the Dial
Place the plastic dial protector over the dial. Slip the centre hole over the hand post so the sheet lies flat and the tool cannot touch the paint or printing. Make sure the sheet is clean and flat.
Step 4: Remove the Second Hand First
The second hand sits highest on the centre post, so it comes off first. Position the tool or lever directly under the hand, close to the post. Lift straight up with even, balanced pressure. Do not rock the tool from side to side.
Step 5: Remove the Minute Hand
Next is the minute hand. Position the tool evenly under the hand and lift straight up. If the hand resists, stop and check the tool’s position. Do not force it.
Step 6: Remove the Hour Hand Last
The hour hand comes off last. It is short and sits closest to the dial, so it is easy to bend or scratch. Position the tool carefully and lift slowly.
Store the Hands Safely
Place each hand in an envelope or tray, labelled by position. Keep the hands flat, and keep any spacer washers with the hand they belong to. Use tweezers rather than your fingers to handle hands.
Refitting the Hands
Refit in the reverse order: hour hand first, then the minute hand, then the second hand.
- Check the sequence. Confirm you have the right hand for each position, and that any spacer washer is in place.
- Fit the hour hand. Place it on the hour wheel and press it on evenly with the hand press.
- Fit the minute hand. Place it on the cannon pinion, check its alignment against the hour hand at 12 o’clock, and press it on evenly.
- Fit the second hand. Place it on the centre seconds post and press it on.
- Check clearance. The hands should clear the dial and each other without rubbing. Turn the movement slowly and watch the hands.
- Test the movement. Run the watch and check that the hands move freely and in time.
Common Mistakes
- Prying sideways. This can bend the hand or break the fragile centre pinion.
- Using tweezers or a knife as a lever. These slip easily and can scratch the dial.
- Pressing with fingers. Uneven pressure can crack the dial or bend the hand.
- Skipping the dial protector. A single slip can mark the dial.
- Losing spacer washers. Some watches have washers between the hand and the dial, and they must go back in the right place.
- Refitting without checking clearance. A hand that touches the crystal or dial will drag or stop.
Luminous and Vintage Dials
Many watches made before about the 1960s used radium-based luminous paint, which is radioactive. Treat these dials with care:
- do not scrape, sand or polish the luminous areas
- wear gloves when handling the dial, and wash your hands afterwards
- do not eat or drink near the watch while you work
- if you are unsure, leave the dial alone and ask a professional
When to Call a Professional
Take the watch to a watchmaker if:
- the dial is valuable, vintage or luminous
- a hand is bent or stuck
- the hands need replacing with a precise match
- the movement needs a service at the same time
- you are not confident about the alignment or clearances
For practice before you try this on a valued watch, use a donor movement. The beginner restoration guide explains how to build that skill. If you are considering a movement swap, the guide to converting a mechanical watch to quartz covers the steps involved, including hand refitting. For scratches on the case and bracelet, see the polishing guide.