Repair and Restoration

What is the most common size of pocket watch?

Pocket watch sizes come from the Lancashire gauge, with 16 and 18 often cited as common American sizes. Learn to measure a movement and read a size chart.

On this page
  1. Quick Answer: The Sizes You Are Most Likely to Meet
  2. How Pocket Watch Sizes Work
  3. Why “Most Common” Is Hard to Pin Down
  4. Measuring Your Movement
  5. Size Chart: Common Lancashire Sizes
  6. E. Howard Letter Sizes
  7. Why Size Matters for Parts
  8. Size Is Not Value

Sizes around 16 and 18 are the ones collectors most often mention for American pocket watches. No authoritative count exists, though, and the answer depends on the maker, the era and the region. The reliable way to find your watch’s size is to measure its movement.

Quick Answer: The Sizes You Are Most Likely to Meet

Collectors often describe sizes 16 and 18 as the ones they encounter most. Those are impressions rather than verified totals. To know your own watch’s size, measure the movement, which takes a few minutes with the right tool.

How Pocket Watch Sizes Work

Pocket watch sizes come from the Lancashire gauge, which was popular in English watchmaking. The American watch industry adopted it. The system starts from a basis of one inch and adds 5/30 of an inch for the fall of the dial. That gives a “naught” size, written 0s, of 1 5/30 inches, or about 29.63 mm.

Each increase or decrease of 1/30 inch makes a new size. For example, size 12 measures 1 17/30 inches, or about 39.79 mm, which is 12 steps above naught. Sizes below naught are written as fractions. Size 6/0s, for instance, is smaller than naught.

Why “Most Common” Is Hard to Pin Down

There is no single published count of pocket watches by size. Makers did not always follow the standard exactly. Some American makers used a larger drop on bigger movements, so a movement labelled 18 can measure larger than the standard 18 figure. Production also changed over time, and makers and regions had their own preferences. A size that was common in one country or decade may be rare in another.

Collector impressions and sales listings are not a measure of total production, so treat any single source with care.

Measuring Your Movement

Measure the movement, not the case. Cases were often made separately from movements and may not match them.

  1. Remove the movement from the case carefully. If you cannot remove it safely, have a watchmaker measure it.
  2. Use a micrometer or precise calipers. Measure the pillar plate on the dial side of the movement, across its widest point.
  3. Record the measurement in millimetres and inches.
  4. Compare it with the chart below, and check whether the maker used a standard or a larger drop.

Size Chart: Common Lancashire Sizes

These figures come from a reference chart. Compare each one with your measurement.

Size Diameter (mm) Diameter (in)
6/0s 25.40 1.000
0s 29.63 1.167
6s 34.71 1.367
10s 38.10 1.500
12s 39.79 1.567
16s 43.18 1.700
18s 44.87 1.767

The same chart notes that many American 18 size movements measure about 45.72 mm (1.800 in), because of the larger drop. A reading near 1.800 inches on an American 18 should not be treated as an error.

E. Howard Letter Sizes

E. Howard & Co. used its own letter-based system in early production. Letter A equals one inch, and each following letter adds 1/16 of an inch. Some early watches from that factory needed special cases made to fit them. If your watch is marked with a letter, look up the E. Howard measurement rather than the Lancashire one.

Why Size Matters for Parts

Size decides which parts fit. A mainspring, a crystal, a dial and a movement must match the case and the barrel. Check the size before you order any part. The mainspring guide explains how barrel size and spring dimensions work together.

Size Is Not Value

A larger or more common size does not automatically mean a more valuable watch. Value depends on the maker, grade, condition and originality. For that, see the guide to telling if a pocket watch is worth money.

The complete guide to repair and restoration

Watch Restoration for Beginners: Tools and First Projects
Read the guide

Keep exploring

Guides from other topics

All topics →