Start With One Question: Is It Quartz or Mechanical?
A watch that keeps stopping usually runs on one of two power sources, and the likely fix depends on which one you have.
- Quartz (battery) watches run on a small battery. The battery powers a quartz crystal that keeps time, and a small motor moves the hands. A quartz watch’s second hand moves in one-second steps.
- Mechanical watches have no battery. A wound mainspring powers a gear train and a balance wheel. Automatic (self-winding) watches are wound by a rotor that moves with your wrist. Manual-wind watches are wound with the crown. A mechanical watch ticks several times per second, while a quartz watch ticks once per second.
Holding the watch to your ear is a quick way to check. If you hear a fast, steady tick, it’s probably mechanical. If the tick is slow and regular, it’s probably quartz. If you can’t hear anything, check the case back or the manufacturer’s listing.
Quick Checks Anyone Can Do
Run through these before anything else:
- Check the crown. Make sure it’s fully pushed in. A crown pulled out to the time-setting position can stop a watch. A screw-down crown should be fully screwed in.
- Check the hands. Look for hands that touch each other, the dial or the crystal. A bent or rubbing hand can stall a quartz movement.
- Wind a mechanical watch. Wind the crown gently in the direction the manual gives. If the watch starts and then stops soon after, it may need more winding or have another fault.
- Think about the battery. On a quartz watch, a second hand that jumps every two seconds usually means the battery is low. A watch that stopped completely may have a flat battery or a battery that has lost contact.
- Think about recent events. Did the watch stop after a drop, after getting wet, after time near a strong magnet, or after a day or two off the wrist?
When a Mechanical Watch Stops
The power has run out. An automatic watch stops when the mainspring has no stored energy left. Many mechanical watches run for roughly 36 to 50 hours on a full wind, and some run longer. If you take an automatic off for a day or two, it can stop. This isn’t damage. Why automatic watches stop when not worn explains how to restart one.
It isn’t wound enough. An automatic watch on a quiet wrist, or one left on a desk, may not wind itself fully. A few gentle turns of the crown can get it going again.
Its lubricants have dried or thickened. The oils inside a watch change with age. Once they dry or thicken, the movement works harder, and the watch may run slowly, stop, or behave differently in different positions. A service fixes this.
It has been magnetized. Speakers, some phones and magnetic clasps can magnetize the hairspring. A magnetized watch often runs fast and may behave erratically. See why a magnetized watch runs fast and how to demagnetize it.
Something inside has been knocked. A hard knock can move parts out of position or damage them. If the watch stopped after a drop, read what to check after a watch stops following a drop.
When a Quartz Watch Stops
The battery is low. A low battery often warns you first. The second hand jumps every two seconds instead of moving every second, and the watch can keep going for a while after that. Replace the battery soon rather than waiting for it to stop. Quartz watch problems covers the two-second tick and how solar and kinetic watches differ.
The battery has lost contact. If the battery or its retaining clip is loose, a knock can break the connection until the watch is moved again. Replacement by a watchmaker usually fixes this.
Moisture or corrosion has got in. Moisture inside the case, or a leaking old battery, can corrode the contacts. Condensation inside a watch crystal explains what fog under the glass means.
Magnets are nearby. Strong magnets can stop a quartz second hand while the magnet is close. The hand often starts again once the magnet is moved away.
When Stopping Is Normal
An automatic watch that stops after being left unworn has simply used up its stored energy. Restarting it is usually straightforward, and stopping on its own doesn’t mean the watch is damaged. What matters is whether it stops while you’re wearing it, runs down much faster than its power reserve, or stops and starts without a cause.
Signs It Needs a Watchmaker
Take the watch to a watchmaker or the brand’s service center if:
- It keeps stopping after you’ve wound it or replaced the battery.
- It stops and restarts with no clear cause.
- The hands move unevenly, stick or catch.
- You hear grinding, scraping or loud rattling.
- It stopped after a drop or after getting wet, or fog has appeared under the crystal.
- The crown is stiff, loose or won’t wind. A crown that won’t wind has several causes, some of which need a watchmaker.
A watchmaker can check the movement under magnification, clean and oil it, demagnetize it and pressure-test the case.
Keep It Running
- Wear automatic watches regularly, or wind them by hand before wearing them after a break.
- Keep watches away from strong magnets, such as speaker magnets and magnetic clasps.
- Keep the crown pushed in or screwed down.
- Have mechanical watches serviced every few years. The right interval depends on the movement and how you use the watch, so ask a watchmaker.
- Change quartz batteries before they run out, and have the seals checked when the battery is changed on a water-resistant watch.
Frequently Asked Questions
How do I restart an automatic watch that has stopped? Unscrew the crown if it’s a screw-down type. Wind gently by hand until the crown feels firm, set the time, and then wear the watch. Why automatic watches stop when not worn has the full steps.
How long does a mechanical watch last? With regular servicing, a mechanical watch can last for decades. Its life depends on how it’s used, how it’s cared for and how often it’s serviced.
Can you overwind a mechanical watch? Most modern automatic and manual-wind movements have a limit that stops winding once the mainspring is full. Forcing the crown can still cause damage, so wind gently and follow the manual.