Repair and Restoration

Cleaning a Mechanical Watch Movement: Ultrasonic Cleaning Basics

How watchmakers clean a mechanical movement in an ultrasonic machine, why home movement cleaning is risky, and the safe steps owners can take instead.

On this page
  1. What “Cleaning the Movement” Means
  2. How Ultrasonic Cleaning Works
  3. The Professional Sequence
  4. Why Home Movement Cleaning Is Risky
  5. Consumer Ultrasonic Cleaners
  6. Safe Things Owners Can Do
  7. Questions to Ask a Watchmaker
  8. Safety Notes
  9. Signs the Movement Needs Cleaning

Cleaning a mechanical movement is professional work. A watchmaker takes the movement apart, cleans each part in a controlled ultrasonic process, rinses and dries the parts, then oils and reassembles the movement and checks its timing. A home attempt can damage fragile parts, remove lubricant the watch needs, or harm the seals. Owners can safely clean the outside of a watch and should leave the movement to a qualified watchmaker.

What “Cleaning the Movement” Means

Cleaning a movement is more than removing dust. Over time, lubricating oil thickens, dries and collects dirt, and tiny particles stick to pivots and gear teeth. A movement clean removes that old oil and grime, so fresh lubricant can go where it is needed. It is usually part of a full service rather than a job on its own.

How Ultrasonic Cleaning Works

An ultrasonic cleaner sends high-frequency sound waves through a liquid. These waves form tiny bubbles that collapse against surfaces and loosen dirt. Watchmakers use water-based cleaning solutions in specialised machines. The parts sit in baskets, and the solution is chosen to suit the metals and finishes involved.

Ultrasonic cleaning is effective, but it is not gentle to everything. Assembled parts, parts fitted with seals, and some materials need extra care, so different parts are often cleaned on different cycles.

The Professional Sequence

A typical professional process has these stages:

  1. Inspection. The watchmaker checks the movement for damage and wear before anything is removed.
  2. Disassembly. The movement is taken apart in an order that protects each part, with parts kept in labelled trays.
  3. Cleaning. Parts go through an ultrasonic bath in a suitable solution.
  4. Rinsing. Parts are rinsed in clean fluid to remove the cleaning solution.
  5. Drying. Parts are dried thoroughly, because trapped liquid can cause corrosion.
  6. Lubrication. Specific oils go on specific points, in very small amounts.
  7. Reassembly. The movement is put back together with care for the fragile parts.
  8. Adjustment and testing. The watchmaker adjusts and times the movement, then tests it.
  9. Case and seal checks. If the watch is water resistant, the seals are checked and the case is pressure tested.

Each stage needs skill, the right equipment and a steady hand.

Why Home Movement Cleaning Is Risky

A home attempt can go wrong in several ways:

  • Fragile parts. The hairspring is finer than a human hair. A small bend can change how the watch runs.
  • Lubrication. Cleaning removes oil. Without the right oil in the right places, parts wear quickly.
  • Magnetism. Magnetised parts can cause timing errors, and tools or equipment can magnetise parts if they are not handled carefully.
  • Solvents. Some solvents used in movement work are flammable and need good ventilation.
  • Seals. Opening a case can affect the gaskets and seals that keep water out.
  • Reassembly. Parts can go back in the wrong orientation, which can stop the watch or damage it.

For these reasons, movement cleaning is normally done by a qualified watchmaker.

Consumer Ultrasonic Cleaners

Consumer ultrasonic cleaners are sold for jewellery and watch parts. Some hobbyists use them, but they are not a substitute for a service. Putting a whole watch into an ultrasonic bath can damage seals, dislodge parts or strip lubricant, and it may still not clean the movement properly. Using one on parts takes training, the right solution and a clear understanding of the materials involved. Never put a sealed watch in one.

Safe Things Owners Can Do

  • Clean the outside. A soft cloth, a soft brush and, where the manufacturer allows it, mild soap are usually enough.
  • Check the seals. When you open the case for a battery change, look for cracks, dryness or deformation in the gaskets.
  • Watch for signs. Moisture under the crystal, a shorter power reserve, changes in timing or a stiff crown all point to a service.
  • Ask for a service. Book a watchmaker for a clean and oil, and ask what the service includes.

For the outside of the watch, see the guide to the best thing to clean watches with.

Questions to Ask a Watchmaker

  • Is the movement fully disassembled for cleaning, or only partly?
  • Which solution and process do you use?
  • How are parts rinsed and dried?
  • Which lubricants do you use, and where?
  • Is the watch timed and tested after reassembly?
  • Is a water-resistance test included, if the watch needs one?

Safety Notes

Movement work involves real hazards:

  • Flammable solvents. Keep them away from heat and open flames, and use them only in a ventilated area.
  • Eye protection. Wear it when handling parts, solvents or machines.
  • Electrical equipment. Keep the machine’s electrical parts dry, and follow the manufacturer’s electrical safety guidance.
  • Disposal. Dispose of used solutions and solvents according to local rules, not down a drain.

Signs the Movement Needs Cleaning

A movement may need a clean and service if you notice:

  • timekeeping that changes over time
  • a power reserve that is shorter than it used to be
  • a stiff or uneven feel when winding or setting
  • a watch that stops or runs unevenly
  • moisture or condensation under the crystal

If you see any of these, have a watchmaker look at the movement. For more on service timing, see how often a mechanical watch should be serviced. For the basics of home watch work, see watch restoration for beginners.

The complete guide to repair and restoration

Watch Restoration for Beginners: Tools and First Projects
Read the guide

Keep exploring

Guides from other topics

All topics →