Start With the Type of Watch
Whether a watch loses or gains time depends on its power source. Quartz and mechanical watches have different weak points.
- Quartz watches usually drift because of the battery or temperature. A weak battery can slow a quartz watch or make the second hand skip.
- Mechanical and automatic watches depend on the mainspring, the lubricants, the balance wheel and the hairspring. Changes in power, friction, temperature and position all affect the rate.
For the full list of causes, why watches lose time covers them in one place. This article focuses on how to tell what’s happening and what to do about it.
Quartz Watches: Battery and Temperature
If a quartz watch is running slow, check the battery first. A weak battery can make the watch fall behind or skip. If the second hand is jumping every two seconds, replace the battery soon. Quartz watch problems covers the two-second tick.
Temperature can shift a quartz crystal’s rate a little. Good quartz movements compensate for this, so a noticeable change in a quartz watch that’s otherwise working usually points to a fault such as a battery issue or moisture.
Mechanical Watches: Power, Oil, Temperature and Position
A mechanical watch’s rate depends on how the mainspring delivers energy to the balance wheel:
- Low power reserve. When an automatic or manual watch is partly wound, the mainspring delivers less steady energy, and the watch can run slow. Wearing an automatic regularly, or winding it by hand, helps keep the power up.
- Dried or thickened oils. Lubricants change with age. Friction increases, and the watch can run slow, run unevenly or stop. A service fixes this.
- Temperature. Metal parts, including the hairspring, expand and contract with temperature. Mechanical watches usually change rate a little in hot and cold conditions.
- Position. Gravity acts on the balance wheel differently in each position. A watch can run at a slightly different rate lying flat, dial up, dial down, or on the wrist. This is normal within limits.
- Shock. A knock can disturb the balance or the jewels. If the error changed suddenly after a drop, see what to check after a watch stops following a drop.
Measure the Error Before Acting
Don’t guess. Measure the error over several days, then decide what to do.
- Pick a reliable time source. A phone that syncs its clock to the network is a good reference.
- Note the time once a day, at the same time of day, for 5 to 7 days.
- Record the position. If you can, note whether the watch was dial up, dial down or on the wrist. Changes in position can change the rate.
- Work out the average gain or loss per day. Then compare the figure with the watch’s rated accuracy, or with a standard quartz figure of about 15 seconds per month.
A steady, small error is usually normal for a mechanical watch. A large or changing error, or one that started suddenly, needs attention.
Fast Running Can Point to Magnetism or Rebanking
A mechanical watch that runs fast can have a magnetized hairspring. Coils that stick together change the rate and often lower the amplitude. See why a magnetized watch runs fast and how to demagnetize it.
A watch that runs fast with a rapid, galloping sound may be rebanking. This is a milder version of overbanking, described below.
Overbanking: When the Balance Wheel Goes Too Far
An overbanked watch is one where the impulse jewel on the balance wheel travels too far. It slips out of the pallet fork slot and gets stuck on the outside of the fork horns. The escapement can’t work properly, and the watch may stop or run erratically.
Overbanking vs. rebanking. In overbanking, the jewel leaves the slot and stays out. In rebanking, the jewel strikes the outside of the fork horn but bounces back into the slot. Rebanking often makes a rapid, galloping sound and makes the watch run fast.
Common causes include:
- A physical shock or drop that knocks the balance or the pallet fork out of alignment.
- Excessive power or high amplitude, for example from a mainspring that is too strong or from lubrication problems.
- Wear or misalignment of guard pins or other escapement parts.
What to do. Overbanking is a watchmaker’s job. Realigning the balance wheel, checking the guard pin and banking pins, and correcting the power all need the right tools and experience. Don’t try to reseat the balance at home. A small misalignment can turn into a costly repair.
When to Have It Serviced
Book a service if:
- The error has changed suddenly, or the watch has started running very fast or very slow.
- It stopped or started running erratically after a drop.
- The error stays large after a wind and a battery check, in a quartz watch.
- The watch hasn’t been serviced for several years.
A watchmaker can measure the rate and amplitude, check for magnetism and overbanking, clean and lubricate the movement, and regulate it. Ask for the timing results before and after the work.