Troubleshooting

Quartz Watch Problems: Stopping, 2-Second Ticks and Misaligned Hands

Fix common quartz watch problems: a watch that stops now and then, a second hand that ticks every two seconds, and hands that no longer match the digital time.

On this page
  1. How a Quartz Watch Keeps Time
  2. Why the Second Hand Jumps Every Two Seconds
  3. Why a Quartz Watch Stops Now and Then
  4. When the Second Hand Won’t Move
  5. When the Hands Don’t Match the Digital Time (Casio)
  6. How Accurate a Quartz Watch Should Be
  7. What to Do Next

How a Quartz Watch Keeps Time

A quartz watch runs on a small battery. The battery powers a tiny quartz crystal, which vibrates at a very steady rate. In most watches that rate is 32,768 times per second. Electronics divide that vibration down to one pulse per second, and a small stepping motor advances the hands with each pulse.

Because the timekeeping is electronic, a quartz watch usually needs little more than a working battery and intact contacts. Its problems tend to be electrical, mechanical in the gear train, or caused by moisture, rather than by winding or oils.

Why the Second Hand Jumps Every Two Seconds

Most quartz watches have a low-battery warning. When the battery voltage falls below a set level, the electronics change the second hand to step every two seconds instead of every second. Some models use a four-second step. The watch keeps time during this phase, but the battery needs replacing soon.

The same symptom can have different causes in different types of quartz watch:

  • Standard battery quartz: The two-second step is an end-of-life signal. Replace the battery soon. It’s not an emergency, but don’t leave it too long.
  • Solar and Eco-Drive watches: These charge a rechargeable cell from light. When the charge is low, the second hand can jump in steps. Place the watch in direct sunlight or bright indoor light for several hours.
  • Kinetic watches: These generate power from wrist movement and store it. Wearing the watch or moving it can build up the charge. If the watch no longer holds a charge after normal wear, it may need servicing.

Why a Quartz Watch Stops Now and Then

A quartz watch that stops and restarts, especially when you knock it, has an intermittent fault. The usual causes are:

  • A loose battery or contact. If the battery or its retaining clip has moved, a knock can break the connection briefly. A watchmaker can reseat or replace the contact.
  • Hands that catch. If the hour, minute or second hand rubs the dial, the crystal or another hand, the stepping motor can stall. Watch the hands as they move. If they touch, a watchmaker can adjust them.
  • Moisture or corrosion. Humidity or a leaking battery can corrode contacts or the circuit. Condensation inside a watch crystal explains what fog under the glass means.
  • Magnetism. Strong magnets, such as the ones in some speakers and chargers, can stop a quartz second hand while the magnet is close. The hand often starts again once the magnet is moved away. For mechanical watches, see a magnetized watch.
  • Impact damage. A hard drop can shift gears, damage the circuit or loosen the hands. See what to check after a watch stops following a drop.

When the Second Hand Won’t Move

If the second hand of a Seiko or other quartz watch isn’t moving at all, work through these steps:

  1. Check the crown. A crown pulled out into the setting position can stop the second hand. Push it in.
  2. Check the power. A solar or kinetic watch may simply be out of charge. Give a solar watch light, or move a kinetic watch to build charge.
  3. Check for a catching hand. Look for a bent second hand or one touching the dial.
  4. Check the battery. Replace it with a matched cell if you’re comfortable doing so. Match the battery code printed on the old cell. If the watch is water-resistant, have the seals checked when the battery is changed.

If the watch still doesn’t run, take it to a watchmaker or the brand’s service center. A watch crown that won’t wind or won’t push in can also stop a movement, so check it too.

When the Hands Don’t Match the Digital Time (Casio)

Some Casio watches combine a digital display with analog hands. The two can fall out of step after a time change, a battery change or a reset. This is usually a setting problem, not a fault.

  • Check the mode. Confirm the watch is in the time-setting mode you intend to use.
  • Use the hand-adjustment function in the manual. Casio models differ, and the button sequences differ between models. Follow the manual for your exact watch rather than a general guide.
  • Don’t force the hands. Don’t push or turn them with fingernails or tools. Use the adjustment method the manual describes.
  • Get it checked if the problem comes back. Repeated misalignment, or hands that won’t move, needs a service.

How Accurate a Quartz Watch Should Be

Standard quartz watches are typically rated to about 15 seconds per month, which works out to roughly half a second per day. Higher-grade quartz movements can be more accurate.

If your watch loses or gains much more than its rated figure, something is wrong. Check the battery first, then the hand positions and the case seal. Changes in temperature can also shift a quartz watch’s rate a little, but a sudden or large error is more likely a fault.

What to Do Next

  • Two-second tick: Replace the battery, or charge the solar cell or kinetic movement.
  • Stops and restarts: Check the crown, the hands and the battery contact.
  • Completely stopped: Check the crown and the hands, then take the watch in. Common reasons a quartz watch has stopped working are listed in order of likelihood.
  • Water-resistant watch after a battery change: Have the seals tested.
  • Problems that persist: Why your watch keeps stopping gives a wider checklist that covers both quartz and mechanical watches.

The complete guide to troubleshooting

Why Your Watch Keeps Stopping (and How to Fix It)
Read the guide

Keep exploring

Guides from other topics

All topics →