Troubleshooting

Why Automatic Watches Stop When Not Worn

Why an automatic watch stops when you take it off, whether that is normal, how to restart it by hand, and when a stop points to a problem worth checking.

On this page
  1. Yes, an Automatic Watch Stops When Its Power Runs Out
  2. How the Rotor and Power Reserve Work
  3. Is a Stopped Automatic Watch Damaged?
  4. How to Restart It
  5. When Stopping Points to a Problem
  6. Keeping It Running
  7. Frequently Asked Questions

Yes, an Automatic Watch Stops When Its Power Runs Out

An automatic watch doesn’t run on a battery. It runs on energy stored in a mainspring, a tightly coiled metal spring inside the movement. Your wrist movement winds that spring. When you take the watch off, the mainspring keeps releasing energy until it’s used up, and then the watch stops. This is normal and doesn’t mean the watch is broken.

How the Rotor and Power Reserve Work

An automatic movement has a weighted rotor that swings as your wrist moves. Gears carry that motion to the mainspring, which stores the energy. The gear train then passes the energy to the escapement and balance wheel, which control the timekeeping.

The power reserve is how long a fully wound watch runs without more winding. Many mechanical watches have a power reserve somewhere around 36 to 50 hours. Some newer movements run considerably longer. Check the manufacturer’s specification for your model.

The reserve is measured from a fully wound state. A watch that has only been partly wound by daily wear may run down sooner than its specification suggests. This is why a watch can stop overnight after a quiet day, even when you wear it.

Is a Stopped Automatic Watch Damaged?

Usually not. A movement that stops because it has run out of power hasn’t necessarily been harmed. The watch simply needs energy to start again.

Repeated stopping that doesn’t match the power reserve, or stopping while worn, is a different matter. Those patterns can point to lubrication problems or other faults. The sections below explain the difference.

How to Restart It

Restarting an automatic watch is usually simple.

  1. Unscrew the crown if the watch has a screw-down crown. Keep the crown in its normal winding position, as the manual describes.
  2. Wind the mainspring. Turn the crown gently in the direction the manual gives, usually clockwise. A few dozen gentle turns is a common starting point, depending on the movement. Stop when the crown feels firm and no longer turns easily.
  3. Set the time. Pull the crown out to the time-setting position and move the hands to the correct time.
  4. Set the date with care. Many watchmakers advise avoiding quick-set date changes in the late-evening to early-morning window, often cited as roughly 9 p.m. to 3 a.m., because the date mechanism is more likely to be engaged then. Check your manual for your model.
  5. Push the crown in and screw it down if applicable. Then wear the watch so your wrist can keep it wound.

Some older automatic movements can’t be wound by hand. These need wrist movement or regular wear to restart. Shaking the watch vigorously is not a substitute for winding. It adds very little energy and isn’t needed.

Some movements have a hacking seconds feature, where the second hand stops when you pull the crown out to set the time. That’s normal.

When Stopping Points to a Problem

Stopping that comes with any of the following signs is worth looking into:

Possible causes include worn parts, dried or thickened lubricant, a crown or winding problem, magnetism, or moisture. You can’t tell which from the symptoms alone. A watchmaker can inspect the movement and find out.

If your automatic watch keeps stopping while you wear it, a wider look at why watches stop covers other common causes.

Keeping It Running

  • Wear it regularly. Daily wrist movement helps replenish the mainspring. How much is enough depends on your activity and the movement.
  • Wind it by hand before wearing it after a long break.
  • Consider a winder if you want one. A winder keeps an automatic running when you’re not wearing it, and many owners use one for watches with complicated calendar functions. For a simple automatic, a winder is convenient but not required. Opinions differ on whether a watch should run constantly, so follow the manufacturer’s guidance.
  • Choose a longer power reserve if you rotate several watches. Some modern movements run for much longer than the typical range.

Frequently Asked Questions

Can you overwind an automatic watch? Most modern automatic movements have a slipping mechanism that limits how tightly the mainspring can be wound during normal winding. Even so, follow the manual and don’t force the crown.

Do you have to wind an automatic watch? Not necessarily. Regular wrist movement winds it. Manual winding helps when you restart a stopped watch or after a period of little activity.

How often should you wind an automatic watch? There is no single schedule. A watch you wear every day may need little winding. A watch you wear occasionally may benefit from a few turns before you put it on.

Does an automatic watch stop if you don’t move enough while wearing it? It can. A sedentary day may not generate enough energy to replace what the watch uses, so the watch can stop even while you’re wearing it.

The complete guide to troubleshooting

Why Your Watch Keeps Stopping (and How to Fix It)
Read the guide

Keep exploring

Guides from other topics

All topics →