The crown is the knob on the side of the case. On most mechanical watches, it does two jobs. It winds the mainspring, which stores the energy that drives the movement. It also sets the time and date. Inside the case, a small set of gears and levers, called the keyless works, decides which job the crown does at any moment.
What the crown does
Turning the crown in one position winds the watch. Pulling it out to another position lets you turn the hands. On a watch with a date, a middle position usually lets you change the date without moving the hands. The exact positions vary from watch to watch, so check the manual for yours.
From the crown to the movement
The crown sits on the end of a thin steel rod called the stem. The stem passes through a tube in the case, and inside the case it connects to the keyless works.
The keyless works are the set of wheels and levers between the stem and the movement. Before watches had crowns, they were wound with a separate key. Keyless winding became practical in the nineteenth century. Turning the crown turns the stem, and the stem turns the parts that wind the spring or set the hands.
The winding and setting positions
In the winding position, the crown is pushed in or screwed down. Turning it turns the winding pinion on the stem. The pinion meshes with the crown wheel, which turns the ratchet wheel that winds the mainspring. Winding pulls the spring tighter and stores more energy.
In the setting position, the crown is pulled out. The stem moves along its length, which changes which gears it drives. Turning the crown in this position turns the setting wheels, and the setting wheels turn the hands.
Many watches with a date have an intermediate position. In that position, the crown turns only the date mechanism, and the hands stay where they are.
The yoke and the clutch
The yoke is a small forked lever in the keyless works. It sits in a groove on a sliding part called the clutch wheel. When you pull the crown out, the setting lever pushes the yoke, and the yoke slides the clutch wheel from the winding position to the setting position.
A yoke spring holds the yoke in place, so the crown stays in the position you choose. The clutch wheel keeps winding and setting separate. This stops the hands from spinning when you wind the watch.
If the yoke or yoke spring is worn or out of position, the crown can feel loose, spin without winding, or fail to shift between positions. These faults are usually a job for a watchmaker.
Winding: the ratchet and the mainspring
A small spring-loaded pawl, called the click, engages the teeth of the ratchet wheel. The click stops the ratchet from turning backward, so the wound spring does not unwind while you turn the crown.
Most automatic movements have a slipping mechanism, called a bridle, that stops the mainspring from being overwound. You cannot damage an automatic by winding it too far. A manual-wind watch is different. It stops with firm resistance when fully wound, and forcing it past that point can break the spring.
Push-pull crowns
A push-pull crown pulls out to its setting positions and pushes back in. It seals the case with gaskets around the stem. It has no locking thread, so it relies on those seals alone.
Push-pull crowns are common on dress watches and everyday watches. They are quick to use. Because the crown can be pulled without unscrewing, there is one less step, but the seal is not as strong as a screw-down design.
Screw-down crowns
A screw-down crown threads onto a tube fixed into the case. When you screw it down, it compresses the gaskets and locks the stem in place. This gives a stronger seal against water and dust.
Screw-down crowns are common on dive watches and water-resistant sports watches. Some are also used on other watches for a secure seal.
Two habits matter with a screw-down crown:
- Unscrew it before you use it. Turn the crown counterclockwise until it springs out. Pulling or turning it while it is still screwed down can damage the threads and the stem. Do not force it.
- Screw it back down after you finish. The water-resistance rating assumes the crown is fully screwed down. Press it in gently, turn it clockwise until it stops, and do not overtighten.
A screw-down crown that will not screw in may have worn or dirty threads. Do not force it. Ask a watchmaker to check it.
Function selector and other crown types
Some watches use a function selector, which cycles the crown through extra functions such as neutral or date. This is more common on high-end sports watches. The mechanism is more complicated, so the manual is the best guide.
Some crowns also carry a pusher, for example to switch functions. Some monopusher chronographs put their single pusher in the crown instead of on the case, so check the manual to see where the pusher sits.
Crown shapes and guards
Crowns come in several shapes. Straight crowns are the most common. Onion and conical crowns were designed to be operated with gloves, and you will often see them on pilot-style watches. Some crowns have a stone set into the top, which is a decorative choice.
Some sports watches have crown guards, which are raised shoulders that protect the crown from knocks. A guard protects the crown but does not change how it works.
Common crown problems and what they mean
- The crown spins but does not wind the watch. The winding parts may be disconnected or worn. Stop winding and take the watch to a watchmaker. Turning the crown harder will not fix it.
- The crown pulls out loosely or comes away. The stem may be broken or the crown may have come loose from the stem. Keep all the pieces.
- A screw-down crown will not screw in. The threads may be worn, damaged or dirty. Do not force it.
- The crown is stiff or gritty. The gaskets may be dry or dirty, or the stem may be bent. This is usually a service job.
- Condensation under the crystal. This suggests a failed seal. Moisture can damage the movement, so have the watch checked promptly.
Frequently asked questions
What is a screw-down crown on a watch?
A screw-down crown threads onto a tube in the case. You unscrew it before you wind or set the watch, and you screw it back down afterward. Screwing it down compresses the seals and gives a stronger water-resistance seal.
What does the yoke do in a watch?
The yoke is a small forked lever that moves the clutch wheel between the winding and setting positions. When you pull the crown out, the setting lever pushes the yoke, and the yoke changes what the crown drives.
Can you overwind a watch?
It depends on the movement. Most automatic watches have a slipping bridle, so they cannot be overwound. A manual-wind watch stops with firm resistance when fully wound, and forcing it past that point can break the spring.
For a quick map of the other parts of the watch, see the parts of a watch. Bezels and crowns both affect a watch’s water resistance, so watch bezels explained covers the other side of the seal.