Identify your case back first
Most wristwatches use one of three main back types. Work out which one you have before you pick a tool.
- Snap-on (pressure-fit): a smooth back with no screws, and a small notch or lip along the edge. You open it with a thin blade.
- Screw-down: a round back with small notches or grooves around the outside. You open it with a case back wrench or a friction ball, turning counter-clockwise.
- Screwed-plate: a flat back held by several tiny screws, usually four, around the edge. You open it with a fine screwdriver.
Good light and a magnifier help. If you still can’t tell, check the manual or the brand’s photos of the back.
The best tool depends on the back type. An adjustable case back wrench suits screw-down backs, a thin blade suits snap-on backs, and a precision screwdriver suits screwed-plate backs. A household knife is a poor match for most of them.
Opening a snap-on back
- Put the watch face-down on a soft cloth.
- Find the notch or lip on the edge of the back. It’s often small, so use a magnifier if you need one.
- Slide a thin, flat tool into the gap, such as a case knife or the tip of a thin flathead screwdriver.
- Lever gently and work around the edge rather than at one point. Keep the tool away from the crown and lugs.
- Lift the back off once it releases.
If the back won’t release, stop and check the notch. Forcing it can scratch or bend the case edge. A watchmaker can open a stubborn back without that damage.
Opening a screw-down back
You need a case back wrench, which has adjustable pins, or a rubber friction ball.
- With a wrench, set the pins into two opposite notches. With a friction ball, press it firmly onto the back.
- Press down firmly, so the tool doesn’t slip.
- Turn counter-clockwise. The back should loosen steadily.
Scissors tips in two opposite notches are a common stand-in, but they slip easily and can mark the back. If the tool slips, stop before the case is damaged.
Removing a screwed-plate back
- Choose a precision screwdriver that fits each screw head exactly. A loose fit can strip the slot.
- Remove each screw and keep it in a small dish so it can’t roll away.
- Lift the back plate straight off. Tilting it can catch the gasket or the movement.
Closing the back
Closing is where most problems happen. These checks help:
- Gasket: make sure it is clean, undamaged and seated in its groove. A pinched gasket stops the back from seating and affects water resistance.
- Alignment: many backs have a notch that must line up with the winding stem or crown. A misaligned back can bend or break the stem.
- Even pressure: for snap-on backs, press with your thumbs on a soft surface, or use a case press with the right dies. Press on the edge of the back, not the crystal.
- Screw-down backs: start by hand to avoid cross-threading, then tighten with the wrench. Stop when it’s snug.
- Screwed-plate backs: tighten each screw a little at a time, in a crisscross order, until they’re all snug.
Why the back won’t close
- The notch isn’t lined up with the stem or crown.
- The gasket has moved out of its groove or is dirty.
- The case is tight by design. Some cases are stiff to close, and Timex models are often described that way. A case press with dies that fit the back is the right tool. Brute force is a common way to damage a case or stem.
Timex and other tight cases
Watch repair forums describe Timex cases as stiff to close. The common advice is to press only on the edge of the back, not on the crystal or bezel, and to use a case press with dies that fit the back’s diameter. A bench vise can work as a press if you protect the case with brass or hard plastic blocks and line the back’s notch up with the stem first. Without that protection, a vise can crack the crystal or snap the stem. One forum post describes a stem coming off after a vise was used to force a back closed.
Gaskets and water resistance
The gasket is what keeps water out. Check it each time you open the back, and replace it if it’s cracked, flattened or dried out. Use the size that matches your model, because a generic gasket may not seal. Closing the back doesn’t prove the watch is still sealed. If the watch is meant to be water-resistant, have it pressure-tested after any work.
Replacement parts
Case backs and gaskets are sold by brand service centres and watch parts suppliers. Match the exact model number, because back types and gasket sizes can vary within a brand.
When to see a watchmaker
- The watch is vintage, gold, or valuable
- The back has an unusual design, or the crystal is front-loaded
- The back won’t open with the right tool
- The watch needs a pressure test after work
For the battery swap itself, see how to change a watch battery at home. For front-loaded or cracked crystals, see how to replace a watch crystal.