Batteries and Cases

How to Replace a Watch Crystal

How to replace a watch crystal safely: check the crystal type, match size and shape, remove the old one, fit the gasket and seat the new glass, then test.

On this page
  1. Can a watch crystal be replaced?
  2. When a crystal needs replacing
  3. Know your crystal type
  4. Find the right replacement
  5. Tools
  6. Replacing the crystal: step by step
  7. Casio vintage watches
  8. Water resistance after a crystal change
  9. When to take it to a watchmaker

Can a watch crystal be replaced?

Yes. Most watch crystals can be replaced, but the job varies a lot with the case design. A simple screw-in case is easier than a watch with a front-loaded crystal or a sealed case. Some crystals are easy to match, and some need a watchmaker’s tools to fit.

When a crystal needs replacing

Light surface scratches are usually cosmetic. A replacement is worth considering when the crystal has:

  • A crack or chip, especially near the edge
  • A deep scratch that hides the hands or the dial
  • A loose or lifting edge
  • Moisture or dust inside the watch, which can mean the seal has failed

A cracked crystal can let moisture in, and moisture can damage the movement, so don’t leave one for long.

Know your crystal type

  • Mineral glass: common on many vintage and budget watches. It’s harder than acrylic but can still scratch or crack.
  • Acrylic (plexiglass): softer and easier to scratch. Light scratches can often be polished out. Deep scratches and cracks usually need a new crystal.
  • Sapphire: very scratch-resistant. Replacing it is usually more involved, and it’s often found on higher-end watches.

Check which material your watch uses before you order a part.

Find the right replacement

Size and shape decide whether a crystal fits. Check these before you buy:

  • Model number, usually on the caseback or in the manual
  • Diameter and thickness of the crystal seat
  • Shape: flat, domed, or with a cyclops magnifier
  • Edge style, and whether the crystal is pressed in or held by a ring

Buy from a supplier that lists the watch model and dimensions. Don’t rely on a photo alone.

Tools

  • A case back opener for your back type (see the case back guide)
  • A crystal press, or a case press with dies that clear the crystal’s face
  • A soft cloth, and plastic or other non-metal tweezers
  • A new gasket matched to the crystal and the case
  • A small tray for screws, gaskets and parts
  • Optional: a hand-lifter for the hands, and a tool for the bezel or retaining ring

Replacing the crystal: step by step

  1. Remove the case back using the right method, and note how it sits.
  2. Take off the bezel or retaining ring, if your model has one. Some are threaded and some are pressed in.
  3. Check whether the hands and dial must come off. Depending on how the crystal is held, they may need to. Hands bend easily, so use a hand-lifter. If you’re unsure, leave this step to a watchmaker.
  4. Take out the old crystal by pressing it out evenly, or by lifting it once the ring is free. Work slowly to avoid chipping the case.
  5. Clean the seat and remove the old gasket. Dust or old gasket residue can stop the new crystal from sitting flat.
  6. Fit the new gasket, then the new crystal, with the correct face towards the outside. Press it in evenly with the correct die.
  7. Refit the bezel or ring, dial and hands, then check the crystal is flat, centred and clean.
  8. Refit the case back and test the watch. Check that it runs, and if it’s water-resistant, arrange a seal test.

Casio vintage watches

Vintage Casio models vary widely, so start with the model number.

  • Check the model number on the caseback or in the manual before you order a part. Similar-looking models can differ in crystal size or shape.
  • Digital watches often have a display module behind the crystal, held in the case. Check how the module is held before you remove anything, and handle the display connections carefully.
  • For many older models, buying a crystal matched to the model number is simpler than trying to repair the original.

Water resistance after a crystal change

The crystal’s gasket is the main seal against water. A gasket of the wrong size, or one that isn’t seated properly, can leave the watch leaking. If the watch is meant to be water-resistant, have it pressure-tested after a crystal change, especially before it goes in the water.

When to take it to a watchmaker

  • The crystal is front-loaded, sapphire, or domed in a shape you can’t match
  • The bezel or case ring is damaged
  • The watch is vintage or valuable
  • You’re not sure whether the movement is safe to remove

A watchmaker’s price depends on the watch, the crystal and the shop, so ask for a quote before any work starts. For a related job, see how to open and close a watch case back, since you’ll usually need the back off first.

The complete guide to batteries and cases

How to Change a Watch Battery at Home
Read the guide

Keep exploring

Guides from other topics

All topics →